Not the cheapest?

Let us know, we will try to beat it!

Coupons PRICE MATCH

⚠️Check Before Soldering

If you need to solder or make any modifications to your item please test the item first. Modification or problematic soldering can cause damage not covered under warranty.

Share This Item:

TeenyF4 Pro Flytower F4 1-2S, 5A, 16x16mm

£24.95 (ex VAT £20.79)

Out of stock
Item discontinued

Want to be notified when this product is back in stock?

SKU: E1A-AC3-ED1 Category: Brand:

This is a super tiny yet cable 16x16mm F4 flight stack, complete with betaflight OSD, Dshot600 5A ESC.  Supports 1-2S lIpo.

TeenyF4 Pro Flytower F4 1-2S, 5A, 16x16mm

£24.95 (ex VAT £20.79)

Out of stock
Item discontinued

Want to be notified when this product is back in stock?

This is a super tiny yet cable 16x16mm F4 flight stack, complete with betaflight OSD, Dshot600 5A ESC.  Supports 1-2S lIpo.

Not the cheapest?

We will try to beat it!

⚠️Always test your item before soldering, issues caused by soldering aren't covered by warranty.

SKU: E1A-AC3-ED1 Category: Brand:

This is a super tiny yet cable 16x16mm F4 flight stack.  The flight controller includes the MPU6000 IMU, built in betaflight OSD, and a buck boost regulator.  The ESC supports a continous current of 5A with bursts to 7A, and runs BLheli_S firmware.  So in short if you are looking for a powerful yet tiny flight stack for your micro quadcopter, the TeenyF4 Pro is what you need.

Key Features

  • Support programmable LED_strip
  • Support BLheli/BLHELI_S suite Pass-through ready
  • Support PPM, Oneshot125,Oneshot42,Multishot, Dshot150, Dshot300, Dshot600
  • Default Dshot600
  • Built-in voltage detection, alarm
  • Built-in Betaflight-OSD
  • Buzzer solder pin
  • LED_STRIP connector

Specification

Flight Controller:

  • Item name: TeenyF4 Pro flight controller board
  • Model: TeenyF4 Pro
  • Processor: STM32F405RGT6
  • Sensor: MPU-6000 ( connected by SPI)
  • Firmware Version: betaflight_3.2.0_OMNIBUSF4SD
    • Built-in betaflgiht OSD
    • Built-in Buck-Boost Converter
  • Input Voltage: 1-2S Lipo
  • Receiver: PPM, IBUS, SBUS, DSM2, DSMX etc.
  • Size: 20*20mm
  • Mounting hole: 16*16mm
  • Mount Hole Diameter: 2mm ( M2 )
  • Weight: 2.2g
  • Application: for Micro FPV brushless drone

5A 4 in 1 ESC: ( Bottom )

  • Item Name: Teenypro 4 In 1 5A BLHeli_S ESC
  • Mode: Teenypro
  • Input Voltage: 1-2S Lipo
  • Con. Current: 5A
  • Peak Current: 7A (5 Seconds)
  • Firmware: BLHELI_S
  • Processor: SILABS EFM8BB21F16G
  • BEC: NO
  • Size: 23x27mm (includes solder pad)
  • Mounting Holes: 16x16mm (M2)
  • Weight: 2.1g
  • Firmware Target: BLHeli_S S_H_50_REV16_7
    • Support Dshot150 Dshot300 Dshot600 Oneshot125 Multishot PWM

Setting up your RX

  • SBUS/IBUS/DSMX receiver please configure RX1 (UART1) as input, and enable Serial_RX
  • PPM receiver don’t need to enable Serial_RX
  • DSM/DSM2/DSMX receiver power from 3.3V
  • SBUS and PPM receiver power from 5V

Included:

  • 1x F4 Flight Controller Board
  • 1x 5A 4 In 1 ESC
  • 1x 6P Cable
  • 8x M2*5+5 Nylon column
  • 8x M2 Nuts
  • 8x M2 Screw

 

Weight 50 g

Reviews

There are no reviews yet.

Only logged in customers who have purchased this product may leave a review.

Share this item on:

Product Meta Information:

SKU: E1A-AC3-ED1 Category: Brand:

This is a super tiny yet cable 16x16mm F4 flight stack.  The flight controller includes the MPU6000 IMU, built in betaflight OSD, and a buck boost regulator.  The ESC supports a continous current of 5A with bursts to 7A, and runs BLheli_S firmware.  So in short if you are looking for a powerful yet tiny flight stack for your micro quadcopter, the TeenyF4 Pro is what you need.

Key Features

  • Support programmable LED_strip
  • Support BLheli/BLHELI_S suite Pass-through ready
  • Support PPM, Oneshot125,Oneshot42,Multishot, Dshot150, Dshot300, Dshot600
  • Default Dshot600
  • Built-in voltage detection, alarm
  • Built-in Betaflight-OSD
  • Buzzer solder pin
  • LED_STRIP connector

Specification

Flight Controller:

  • Item name: TeenyF4 Pro flight controller board
  • Model: TeenyF4 Pro
  • Processor: STM32F405RGT6
  • Sensor: MPU-6000 ( connected by SPI)
  • Firmware Version: betaflight_3.2.0_OMNIBUSF4SD
    • Built-in betaflgiht OSD
    • Built-in Buck-Boost Converter
  • Input Voltage: 1-2S Lipo
  • Receiver: PPM, IBUS, SBUS, DSM2, DSMX etc.
  • Size: 20*20mm
  • Mounting hole: 16*16mm
  • Mount Hole Diameter: 2mm ( M2 )
  • Weight: 2.2g
  • Application: for Micro FPV brushless drone

5A 4 in 1 ESC: ( Bottom )

  • Item Name: Teenypro 4 In 1 5A BLHeli_S ESC
  • Mode: Teenypro
  • Input Voltage: 1-2S Lipo
  • Con. Current: 5A
  • Peak Current: 7A (5 Seconds)
  • Firmware: BLHELI_S
  • Processor: SILABS EFM8BB21F16G
  • BEC: NO
  • Size: 23x27mm (includes solder pad)
  • Mounting Holes: 16x16mm (M2)
  • Weight: 2.1g
  • Firmware Target: BLHeli_S S_H_50_REV16_7
    • Support Dshot150 Dshot300 Dshot600 Oneshot125 Multishot PWM

Setting up your RX

  • SBUS/IBUS/DSMX receiver please configure RX1 (UART1) as input, and enable Serial_RX
  • PPM receiver don’t need to enable Serial_RX
  • DSM/DSM2/DSMX receiver power from 3.3V
  • SBUS and PPM receiver power from 5V

Included:

  • 1x F4 Flight Controller Board
  • 1x 5A 4 In 1 ESC
  • 1x 6P Cable
  • 8x M2*5+5 Nylon column
  • 8x M2 Nuts
  • 8x M2 Screw

 

Weight 50 g

Reviews

There are no reviews yet.

Only logged in customers who have purchased this product may leave a review.

TeenyF4 Pro Flytower F4 1-2S, 5A, 16x16mm

Out of stock
Item discontinued