Not the cheapest?

Let us know, we will try to beat it!

Coupons PRICE MATCH

⚠️Check Before Soldering

If you need to solder or make any modifications to your item please test the item first. Modification or problematic soldering can cause damage not covered under warranty.

Share This Item:

Matek Crossfire to PWM Converter – CRSF PWM 6

£4.45 (ex VAT £3.71)

In stock

SKU: B1C-A0E-D02 Category: Tags: , Brand:

The MATEKSYS CRSF PWM 6 is a Crossfire to PWM Converter with 2 UARTS and 6 PWM Outputs. This converter supports any Crossfire Protocol receivers, such as the 433MHz, 868MHz, 915MHz, or 2.4GHz.

Matek Crossfire to PWM Converter – CRSF PWM 6

£4.45 (ex VAT £3.71)

In stock

The MATEKSYS CRSF PWM 6 is a Crossfire to PWM Converter with 2 UARTS and 6 PWM Outputs. This converter supports any Crossfire Protocol receivers, such as the 433MHz, 868MHz, 915MHz, or 2.4GHz.

Not the cheapest?

We will try to beat it!

⚠️Always test your item before soldering, issues caused by soldering aren't covered by warranty.

SKU: B1C-A0E-D02 Category: Tags: , Brand:

Features

  • Compatible with Crossfire Receivers Only
  • No 5V Regulator Built-in
  • Built-in Current Sensor
  • Failsafe Value AutoSet
  • Firmware Upgradeable
  • 6 PWM Outputs
  • 2 UARTS

Mateksys crossfire to pwm converter crsf pwm 6 info

PINOUTS AND PADS

  • 4v5 pad voltage = 5V pad voltage -0.3V, make sure the voltage on the 5V pad is not higher than receiver and GPS rated voltage.
  • Tx2/Rx2(UART2) for GPS/firmware update/setting parameters
  • Tx1/Rx1(UART1) for CRSF protocol Receiver
  • Vbat: Battery voltage sensing (0~36V)
  • Curr: current sensor signal (0~3.3V)
  • 1~10: CH1~CH10 PWM outputs
  • G: ground

FAILSAFE

  • Failsafe value is set automatically after the CRSF-PWM board is powered on and receives the CRSF signal. LED blinks 8 times quickly.
  • Failsafe value = The PWM value of each channel(except CH3) when the CRSF signal is received by the CRSF-PWM board for the first time
  • CH3 is specially arranged for the throttle, Failsafe value = 988 by default.
  • Put the throttle joystick to the lowest point, put AIL(Roll), ELE(Pitch), RUD(Yaw) middle before powering on the receiver.

LED STATUS

  • Slow blinks: CRSF-PWM board doesn’t receive a CRSF signal, e.g., the receiver is not bound with the transmitter, the receiver is not connected to UART1 of the CRSF-PWM board.
  • 8x quick blinks: CRSF-PWM board received CRSF signal and failsafe value is saved.
  • 2x slow blinks between 8x fast blink and solid on: CLI mode is active
  • Solid ON: CRSF-PWM board and receiver are working normally

GPS TELEMETRY

  • Troubleshooting for no GPS telemetry, double-check the wiring between GPS and CRSF-PWM board, some u-Blox GPS may don’t output NMEA protocol, you need to be reverted GPS to the default configuration in u-center.
  • Sensors(GPS, GSpd, Hdg, Alt, Sats) will blink in the Transmitter TELEMETRY tab once the CRSF-PWM board has a connection with GPS.
  • GPS “TX” to CRSF-PWM board “RX” Single wire half-duplex UART connection, CRSF-PWM board “TX” to GPS “RX” is not essential.
  • with OpenTX Telemetry Logging, You can plot your flight path or search the lost plane.
  • u-Blox series GPS can output the “0+1 – UBX+NMEA” protocol by default
  • Compatible with GPS NMEA protocol, 1Hz, Baud 9600~115200
  • Support GPS Telemetry ID: GPS, GSpd, Hdg, Alt, Sats

TIM & PWM FREQUENCY

  • PWM frequency on all 10x Channels can be configured according to TIM
  • PWM runs at 50Hz by default
  • TIM3: CH5, CH6, CH7, CH8
  • TIM2: CH1, CH2, CH4
  • TIM1: CH9, CH10
  • TIM16: CH3

CLI MODE

  • If the CRSF-PWM board doesn’t detect GPS connected to UART2 within 10 seconds after powering on, CLI mode will active.
  • After CLI mode is active, the CRSF-PWM board can be connected to the configurator via USB-TTL module/FC passthrough.
  • CLI mode has no effect on receiver CRSF signal and PWM outputs
  • In CLI mode, CRSF-PWM board firmware can be updated

Specifications

  • Support: Any CRSF protocol receivers (including 433MHz, 868MHz, 915MHz, 2.4GHz)
  • Current sensor: Compatible with External (0-3.3V)
  • Telemetry ID: RxBt, Curr, Capa, Bat%, GPS, GSpd, Hdg, Alt, Sats
  • PWM frequency configurable (50Hz default, 100,160,330, 400Hz)
  • 36V Max. battery voltage sense (1K:10K voltage divider built-in)
  • Rated voltage: 4~9V @5V pad, 0~36V @vBAT, 0-3.3V Curr
  • Vbat and Current sensor scale configurable
  • UARTs (for Receiver and GPS): 2
  • Size: 25mm x 16mm
  • PWM outputs: 10
  • Weight: 1.3g

Includes

  • 1x MATEKSYS CRSF-PWM-6 Converter
  • 1x Dupont 2.54 Pins

 

Weight 100 g
Dimensions 10 × 5 × 5 cm
Frequency

Reviews

There are no reviews yet.

Only logged in customers who have purchased this product may leave a review.

Share this item on:

Product Meta Information:

SKU: B1C-A0E-D02 Category: Tags: , Brand:

Features

  • Compatible with Crossfire Receivers Only
  • No 5V Regulator Built-in
  • Built-in Current Sensor
  • Failsafe Value AutoSet
  • Firmware Upgradeable
  • 6 PWM Outputs
  • 2 UARTS

Mateksys crossfire to pwm converter crsf pwm 6 info

PINOUTS AND PADS

  • 4v5 pad voltage = 5V pad voltage -0.3V, make sure the voltage on the 5V pad is not higher than receiver and GPS rated voltage.
  • Tx2/Rx2(UART2) for GPS/firmware update/setting parameters
  • Tx1/Rx1(UART1) for CRSF protocol Receiver
  • Vbat: Battery voltage sensing (0~36V)
  • Curr: current sensor signal (0~3.3V)
  • 1~10: CH1~CH10 PWM outputs
  • G: ground

FAILSAFE

  • Failsafe value is set automatically after the CRSF-PWM board is powered on and receives the CRSF signal. LED blinks 8 times quickly.
  • Failsafe value = The PWM value of each channel(except CH3) when the CRSF signal is received by the CRSF-PWM board for the first time
  • CH3 is specially arranged for the throttle, Failsafe value = 988 by default.
  • Put the throttle joystick to the lowest point, put AIL(Roll), ELE(Pitch), RUD(Yaw) middle before powering on the receiver.

LED STATUS

  • Slow blinks: CRSF-PWM board doesn’t receive a CRSF signal, e.g., the receiver is not bound with the transmitter, the receiver is not connected to UART1 of the CRSF-PWM board.
  • 8x quick blinks: CRSF-PWM board received CRSF signal and failsafe value is saved.
  • 2x slow blinks between 8x fast blink and solid on: CLI mode is active
  • Solid ON: CRSF-PWM board and receiver are working normally

GPS TELEMETRY

  • Troubleshooting for no GPS telemetry, double-check the wiring between GPS and CRSF-PWM board, some u-Blox GPS may don’t output NMEA protocol, you need to be reverted GPS to the default configuration in u-center.
  • Sensors(GPS, GSpd, Hdg, Alt, Sats) will blink in the Transmitter TELEMETRY tab once the CRSF-PWM board has a connection with GPS.
  • GPS “TX” to CRSF-PWM board “RX” Single wire half-duplex UART connection, CRSF-PWM board “TX” to GPS “RX” is not essential.
  • with OpenTX Telemetry Logging, You can plot your flight path or search the lost plane.
  • u-Blox series GPS can output the “0+1 – UBX+NMEA” protocol by default
  • Compatible with GPS NMEA protocol, 1Hz, Baud 9600~115200
  • Support GPS Telemetry ID: GPS, GSpd, Hdg, Alt, Sats

TIM & PWM FREQUENCY

  • PWM frequency on all 10x Channels can be configured according to TIM
  • PWM runs at 50Hz by default
  • TIM3: CH5, CH6, CH7, CH8
  • TIM2: CH1, CH2, CH4
  • TIM1: CH9, CH10
  • TIM16: CH3

CLI MODE

  • If the CRSF-PWM board doesn’t detect GPS connected to UART2 within 10 seconds after powering on, CLI mode will active.
  • After CLI mode is active, the CRSF-PWM board can be connected to the configurator via USB-TTL module/FC passthrough.
  • CLI mode has no effect on receiver CRSF signal and PWM outputs
  • In CLI mode, CRSF-PWM board firmware can be updated

Specifications

  • Support: Any CRSF protocol receivers (including 433MHz, 868MHz, 915MHz, 2.4GHz)
  • Current sensor: Compatible with External (0-3.3V)
  • Telemetry ID: RxBt, Curr, Capa, Bat%, GPS, GSpd, Hdg, Alt, Sats
  • PWM frequency configurable (50Hz default, 100,160,330, 400Hz)
  • 36V Max. battery voltage sense (1K:10K voltage divider built-in)
  • Rated voltage: 4~9V @5V pad, 0~36V @vBAT, 0-3.3V Curr
  • Vbat and Current sensor scale configurable
  • UARTs (for Receiver and GPS): 2
  • Size: 25mm x 16mm
  • PWM outputs: 10
  • Weight: 1.3g

Includes

  • 1x MATEKSYS CRSF-PWM-6 Converter
  • 1x Dupont 2.54 Pins

 

Weight 100 g
Dimensions 10 × 5 × 5 cm
Frequency

Reviews

There are no reviews yet.

Only logged in customers who have purchased this product may leave a review.

Matek Crossfire to PWM Converter – CRSF PWM 6

In stock