Not the cheapest?

Let us know, we will try to beat it!

Coupons PRICE MATCH

⚠️Check Before Soldering

If you need to solder or make any modifications to your item please test the item first. Modification or problematic soldering can cause damage not covered under warranty.

Share This Item:

Kakute F7

(3 customer reviews)

£35.95 (ex VAT £29.96)

Out of stock
Item discontinued

Want to be notified when this product is back in stock?

SKU: 11033 Category: Brand:

£35.95 (ex VAT £29.96)

Out of stock
Item discontinued

Want to be notified when this product is back in stock?

Not the cheapest?

We will try to beat it!

⚠️Always test your item before soldering, issues caused by soldering aren't covered by warranty.

SKU: 11033 Category: Brand:

The Holybro Kakute F7 flight controller makes it easy to build your multirotor. It integrates flight controller (FC) and onscreen display (OSD) in one. The Kakute F7’s layout makes it easy to wire up the other components of the multirotor while keeping the build neat and tidy.

Key Features

  • Supports Betaflight, Butterflight, and Cleanflight.
  • Betaflight OSD. Change PIDs, adjust common configuration parameters, and change video transmitter channel and power level, all using your transmitter sticks and goggles.
  • Soft-mounting built in. The IMU (“gyro”) chip on this board is mounted on vibration-isolating foam. This means that there is no need to soft-mount the board itself.
  • High-performance / low-noise / high sensitivity IMU. ICM20689 with 6-axis gyro and accelerometer. Can run at up to 32 kHz sampling rate.
  • Ready for autonomous flight: Integrated BMP280 barometer and SCL/SDA pads for use with external GPS/magnetometer units.
  • 2 oz. copper PCB allows up to 120A maximum continuous current.
  • Dedicated bootloader button for easy firmware flashing.
  • Low-profile design fits into even very compact frames.
  • Input voltage 7v to 42v. Power the board directly from the flight pack, up to 6S (on ?B+? pad only).
  • Automatic voltage monitoring. No need to run a separate vBat wire for voltage monitoring; the Kakute F7 monitors voltage directly from the power supply.
  • Filtered voltage output for clean, noise-free video. On-board regulators output 5v at up to 2 amps and 3.3v at up to 200 mA to power peripherals such as receiver, video transmitter, FPV camera, or LED strip.
  • Supports BLHeli pass-through for easy ESC upgrade and configuration.

Specification

  • MCU: STM32F745 32-bit processor
  • IMU: ICM20689 (SPI)
  • Barometer: BMP280
  • Current Sensor: Approximately 130 amps maximum measurable value
  • USB VCP Driver (all UARTs usable simultaneously; USB does not take up a UART)
  • 6 hardware UARTS (UART1,2,3,4,6,7)
  • All UARTS support hardware inversion. SBUS, SmartPort, and other inverted protocols work on any UART without “uninvert hack”
  • Supports serial receivers (SBUS, iBus, Spektrum, Crossfire) only. PPM and PWM receivers are not supported
  • TF card for Blackbox logging
  • Dimensions: 35x41x7mm (includes foam-mounted gyro board in height)
  • Mounting Holes: Standard 30.5mm square to center of holes
  • Weight: 9g

Package Includes

  • KakuteF7 *1
  • Foam*2
  • FFC*1
  • JST SH 8pin 150mm cable*1
Weight 30 g

3 reviews for Kakute F7

  1. Jay

    What an i say but always love holybro had there f4 fc now moved to there f7 fc love them plus unmannedtech great services

  2. Brian

    Great fc easy to connect(4in1 esc)and set up fantastic performance.

  3. Frank Morris

    Used the same soldering iron, heat and tin to build the rest of the quad. However on this board, the solder just wouldn’t stick to a large majority of the pads. Feels like there is a coating on them. Totally unimpressed.

Only logged in customers who have purchased this product may leave a review.

Share this item on:

Product Meta Information:

SKU: 11033 Category: Brand:

The Holybro Kakute F7 flight controller makes it easy to build your multirotor. It integrates flight controller (FC) and onscreen display (OSD) in one. The Kakute F7’s layout makes it easy to wire up the other components of the multirotor while keeping the build neat and tidy.

Key Features

  • Supports Betaflight, Butterflight, and Cleanflight.
  • Betaflight OSD. Change PIDs, adjust common configuration parameters, and change video transmitter channel and power level, all using your transmitter sticks and goggles.
  • Soft-mounting built in. The IMU (“gyro”) chip on this board is mounted on vibration-isolating foam. This means that there is no need to soft-mount the board itself.
  • High-performance / low-noise / high sensitivity IMU. ICM20689 with 6-axis gyro and accelerometer. Can run at up to 32 kHz sampling rate.
  • Ready for autonomous flight: Integrated BMP280 barometer and SCL/SDA pads for use with external GPS/magnetometer units.
  • 2 oz. copper PCB allows up to 120A maximum continuous current.
  • Dedicated bootloader button for easy firmware flashing.
  • Low-profile design fits into even very compact frames.
  • Input voltage 7v to 42v. Power the board directly from the flight pack, up to 6S (on ?B+? pad only).
  • Automatic voltage monitoring. No need to run a separate vBat wire for voltage monitoring; the Kakute F7 monitors voltage directly from the power supply.
  • Filtered voltage output for clean, noise-free video. On-board regulators output 5v at up to 2 amps and 3.3v at up to 200 mA to power peripherals such as receiver, video transmitter, FPV camera, or LED strip.
  • Supports BLHeli pass-through for easy ESC upgrade and configuration.

Specification

  • MCU: STM32F745 32-bit processor
  • IMU: ICM20689 (SPI)
  • Barometer: BMP280
  • Current Sensor: Approximately 130 amps maximum measurable value
  • USB VCP Driver (all UARTs usable simultaneously; USB does not take up a UART)
  • 6 hardware UARTS (UART1,2,3,4,6,7)
  • All UARTS support hardware inversion. SBUS, SmartPort, and other inverted protocols work on any UART without “uninvert hack”
  • Supports serial receivers (SBUS, iBus, Spektrum, Crossfire) only. PPM and PWM receivers are not supported
  • TF card for Blackbox logging
  • Dimensions: 35x41x7mm (includes foam-mounted gyro board in height)
  • Mounting Holes: Standard 30.5mm square to center of holes
  • Weight: 9g

Package Includes

  • KakuteF7 *1
  • Foam*2
  • FFC*1
  • JST SH 8pin 150mm cable*1
Weight 30 g

3 reviews for Kakute F7

  1. Jay

    What an i say but always love holybro had there f4 fc now moved to there f7 fc love them plus unmannedtech great services

  2. Brian

    Great fc easy to connect(4in1 esc)and set up fantastic performance.

  3. Frank Morris

    Used the same soldering iron, heat and tin to build the rest of the quad. However on this board, the solder just wouldn’t stick to a large majority of the pads. Feels like there is a coating on them. Totally unimpressed.

Only logged in customers who have purchased this product may leave a review.

Kakute F7
Kakute F7

Out of stock
Item discontinued