Not the cheapest?

Let us know, we will try to beat it!

Coupons PRICE MATCH

⚠️Check Before Soldering

If you need to solder or make any modifications to your item please test the item first. Modification or problematic soldering can cause damage not covered under warranty.

Share This Item:

iFlight Protek35 Analogue Cinematic Mini Quadcopter (PNP)

£179.95 (ex VAT £149.96)

Out of stock
Item discontinued

Want to be notified when this product is back in stock?

SKU: 015-020-25F Category: Tags: , , Brand:

Equipped with all new 2203.5 motors for more power and less heat. We were able to increase speed and thrust by 50% compared to it’s 3inch predecessor which gives a lot more room for a lot more fun. Our GPS measured maximum speed was above 120km/h and a maximum thrust of 750g per motor (3kg in total) would even carry heavier cams than a Gopro but also do some loaded punch outs or light freestyle moves.

This quadcopter does not have any receiver installed out of the box so you will need to add your own depending on what R/C system you are using.

iFlight Protek35 Analogue Cinematic Mini Quadcopter (PNP)

£179.95 (ex VAT £149.96)

Out of stock
Item discontinued

Want to be notified when this product is back in stock?

Equipped with all new 2203.5 motors for more power and less heat. We were able to increase speed and thrust by 50% compared to it’s 3inch predecessor which gives a lot more room for a lot more fun. Our GPS measured maximum speed was above 120km/h and a maximum thrust of 750g per motor (3kg in total) would even carry heavier cams than a Gopro but also do some loaded punch outs or light freestyle moves.

This quadcopter does not have any receiver installed out of the box so you will need to add your own depending on what R/C system you are using.

Not the cheapest?

We will try to beat it!

⚠️Always test your item before soldering, issues caused by soldering aren't covered by warranty.

SKU: 015-020-25F Category: Tags: , , Brand:

After our very popular 3inch Cinematic EVA bumper BumbleBee and Green Hornet CineWhoop series, we were trying to increase performance and reduce weight for an even better and longer flight experience for a wide variety of use.

Our all new 3.5inch project is finally ready for all you content creators or those guys who like to wear some protection every now and then. Prop protection is what we’re talking about here…

ProTek is not necessarily just a Cinewhoop series but far more. Equipped with all new 2203.5 motors for more power and less heat. We were able to increase speed and thrust by 50% compared to it’s 3inch predecessor which gives a lot more room for a lot more fun. Our GPS measured maximum speed was above 120km/h and a maximum thrust of 750g per motor (3kg in total) would even carry heavier cams than a Gopro but also do some loaded punch outs or light freestyle moves.

A lot of thought was put into the different assembly options. Our stock BNF will ship in the standard configuration but you can either do a pusher mod (flip the build upside down) or a lite mod (remove the protective plastic for weight optimisation).

Durable plastic protectors with copper standoffs, portable compact design, easy accessible UBS port without disassembly, LED battery status, lost model buzzer and a universal GoPro TPU for a full size or naked GoPro. If you wanna go extra light, get one of our 5V balance plug GoPro power cables to get rid of the internal battery

Features

  • No Props or frame in view!
  • High performance True-AIO Board Beast Whoop F7 AIO 45A to save weight and space
  • T700 Quality Carbon (40% more tensile strength compared to common 3K carbon)
  • Lightweight one-piece frame design (Less flexibility, more Rigid, more Durable)
  • Low Resonance frame construction (Less Jello, more Cinematic footage)
  • Caddx.us Turbo Eos V2 FPVCam 2.1mm 16:9 NTSC
  • Butter smooth 2203.5 3600KV (4S)
  • Pre-tuned with smooth freestyle settings

 

 

Factory Setup Files, Pinouts and Wiring Guides

Iflight have provided all of their factory dumps, along with frame assembly, and electronics wiring guides on their google drive folder

ProTek25 HD Quad BNF Included Components and Parts

  • 1x ProTek35 Analog quadcopter BNF with Caddx.us Turbo Eos V2 FPVCam
  • 2x TPU camera side plate soft mount
  • 2x Nazgul 3535 propeller (Set of 4 – Color May Vary)
  • 1x iFlight Lipo Strap 15*150mm (Color May Vary)
  • 1x iFlight Lipo Strap 15*250mm (Color May Vary)

ProTek35 BNF Specs:

  • – Board Beast Whoop F7 AIO 45A
  • – Motor: XING 2203.5 3600KV (4S)
  • – Wheelbase: 151mm
  • – Body Size: 118*94.5mmmm
  • – Bottom plate thickness: 3.5mm
  • – Top plate thickness: 2mm
  • – Top and bottom plate spacing: 20mm (aluminum standoff height)
  • – Propeller size: 3.5 inch
  • – FC pattern: 25.5*25.5mm / 20*20mmmm
  • – FPV cam spacing: 20mm
  • – Weight: 305g (without battery)

FC // Beast F7 AIO

Specification:

  • MCU: BGA-STM32F745
  • Gyro: MPU6000
  • Blackbox: 8Mb Onboard Flash
  • BEC output: 5V 2.5A
  • Barometer: BMP280
  • Connector: Micro-USB
  • OSD: AT7456E
  • FC Firmware:IFLIGHT_F745_AIO
  • Mounting pattern: 25.5*25.5mm φ3mm
  • Dimensions: 32.5*32.5mm
  • Weight: 8.5g

ESC // 45A 2-6S

Specification:

  • Uarts: 5
  • Current Sensor: Yes
  • Input: 2-6S LIPO
  • Current scale: 200
  • Constant: 45A / Burst: 50A
  • BLHeli: BLHeli-S
  • Telemetry: no
  • ESC Firmware: BlheliS G-H-30
  • Mounting pattern: 25.5*25.5mm/Φ3mm
  • Dimensions: 32.5*32.5mm

VTX// SucceX Force 5.8g 800mW VTX Adjustable

  • – The output power is stable;
  • – Transmit power 4 gear switch: 25mW/200mW/400mW/800mW;
  • – Output 48 frequency points,
  • – Frequency lock fast, the boot does not interfere with companions;
  • – Built-in output power self-check function;
  • – Full format video format: NTSC /PAL;
  • – Wide input voltage range. low power consumption:
  •   7V~36V,+12V/380mA@800mW;
  • – Small size:36*36*3mm
  • – Mounting holes 4-M3
  • – Lightweight: 7.2g(excluding antenna)

Additional Suggested Parts

  • 4S 95C 1300mAh
  • iFlight FPV Goggles with DVR Function

Important

A receiver is not included with this quadcopter, you will need to purchase and install your own that will require some soldering and configuration via Betaflight.

Weight 450 g
Dimensions 10 × 10 × 5 cm
Prop Diameter

Reviews

There are no reviews yet.

Only logged in customers who have purchased this product may leave a review.

Share this item on:

Product Meta Information:

SKU: 015-020-25F Category: Tags: , , Brand:

After our very popular 3inch Cinematic EVA bumper BumbleBee and Green Hornet CineWhoop series, we were trying to increase performance and reduce weight for an even better and longer flight experience for a wide variety of use.

Our all new 3.5inch project is finally ready for all you content creators or those guys who like to wear some protection every now and then. Prop protection is what we’re talking about here…

ProTek is not necessarily just a Cinewhoop series but far more. Equipped with all new 2203.5 motors for more power and less heat. We were able to increase speed and thrust by 50% compared to it’s 3inch predecessor which gives a lot more room for a lot more fun. Our GPS measured maximum speed was above 120km/h and a maximum thrust of 750g per motor (3kg in total) would even carry heavier cams than a Gopro but also do some loaded punch outs or light freestyle moves.

A lot of thought was put into the different assembly options. Our stock BNF will ship in the standard configuration but you can either do a pusher mod (flip the build upside down) or a lite mod (remove the protective plastic for weight optimisation).

Durable plastic protectors with copper standoffs, portable compact design, easy accessible UBS port without disassembly, LED battery status, lost model buzzer and a universal GoPro TPU for a full size or naked GoPro. If you wanna go extra light, get one of our 5V balance plug GoPro power cables to get rid of the internal battery

Features

  • No Props or frame in view!
  • High performance True-AIO Board Beast Whoop F7 AIO 45A to save weight and space
  • T700 Quality Carbon (40% more tensile strength compared to common 3K carbon)
  • Lightweight one-piece frame design (Less flexibility, more Rigid, more Durable)
  • Low Resonance frame construction (Less Jello, more Cinematic footage)
  • Caddx.us Turbo Eos V2 FPVCam 2.1mm 16:9 NTSC
  • Butter smooth 2203.5 3600KV (4S)
  • Pre-tuned with smooth freestyle settings

 

 

Factory Setup Files, Pinouts and Wiring Guides

Iflight have provided all of their factory dumps, along with frame assembly, and electronics wiring guides on their google drive folder

ProTek25 HD Quad BNF Included Components and Parts

  • 1x ProTek35 Analog quadcopter BNF with Caddx.us Turbo Eos V2 FPVCam
  • 2x TPU camera side plate soft mount
  • 2x Nazgul 3535 propeller (Set of 4 – Color May Vary)
  • 1x iFlight Lipo Strap 15*150mm (Color May Vary)
  • 1x iFlight Lipo Strap 15*250mm (Color May Vary)

ProTek35 BNF Specs:

  • – Board Beast Whoop F7 AIO 45A
  • – Motor: XING 2203.5 3600KV (4S)
  • – Wheelbase: 151mm
  • – Body Size: 118*94.5mmmm
  • – Bottom plate thickness: 3.5mm
  • – Top plate thickness: 2mm
  • – Top and bottom plate spacing: 20mm (aluminum standoff height)
  • – Propeller size: 3.5 inch
  • – FC pattern: 25.5*25.5mm / 20*20mmmm
  • – FPV cam spacing: 20mm
  • – Weight: 305g (without battery)

FC // Beast F7 AIO

Specification:

  • MCU: BGA-STM32F745
  • Gyro: MPU6000
  • Blackbox: 8Mb Onboard Flash
  • BEC output: 5V 2.5A
  • Barometer: BMP280
  • Connector: Micro-USB
  • OSD: AT7456E
  • FC Firmware:IFLIGHT_F745_AIO
  • Mounting pattern: 25.5*25.5mm φ3mm
  • Dimensions: 32.5*32.5mm
  • Weight: 8.5g

ESC // 45A 2-6S

Specification:

  • Uarts: 5
  • Current Sensor: Yes
  • Input: 2-6S LIPO
  • Current scale: 200
  • Constant: 45A / Burst: 50A
  • BLHeli: BLHeli-S
  • Telemetry: no
  • ESC Firmware: BlheliS G-H-30
  • Mounting pattern: 25.5*25.5mm/Φ3mm
  • Dimensions: 32.5*32.5mm

VTX// SucceX Force 5.8g 800mW VTX Adjustable

  • – The output power is stable;
  • – Transmit power 4 gear switch: 25mW/200mW/400mW/800mW;
  • – Output 48 frequency points,
  • – Frequency lock fast, the boot does not interfere with companions;
  • – Built-in output power self-check function;
  • – Full format video format: NTSC /PAL;
  • – Wide input voltage range. low power consumption:
  •   7V~36V,+12V/380mA@800mW;
  • – Small size:36*36*3mm
  • – Mounting holes 4-M3
  • – Lightweight: 7.2g(excluding antenna)

Additional Suggested Parts

  • 4S 95C 1300mAh
  • iFlight FPV Goggles with DVR Function

Important

A receiver is not included with this quadcopter, you will need to purchase and install your own that will require some soldering and configuration via Betaflight.

Weight 450 g
Dimensions 10 × 10 × 5 cm
Prop Diameter

Reviews

There are no reviews yet.

Only logged in customers who have purchased this product may leave a review.

iFlight Protek35 Analogue Cinematic Mini Quadcopter (PNP)

Out of stock
Item discontinued