Not the cheapest?

Let us know, we will try to beat it!

Coupons PRICE MATCH

⚠️Check Before Soldering

If you need to solder or make any modifications to your item please test the item first. Modification or problematic soldering can cause damage not covered under warranty.

Share This Item:

HolyBro PM06 V2 2-14S Power Module

£19.95 (ex VAT £16.63)

Only 1 left in stock

SKU: H15019 Category: Brand:

The PM06 Power Module is a must-have for any drone builder. It supplies clean 5.2V power to your flight controller and 4 ESCs, with a wide input voltage range of 2S-14S and impressive current ratings of 70A continuous and 120A burst. It also offers precise current consumption and battery voltage measurements through an analog signal. Comes with pre-soldered wires, a capacitor, and an XT60 connector. Compact and lightweight at 35x35x5mm and 24g. Not compatible with Pixhawk 5X & 6X.

HolyBro PM06 V2 2-14S Power Module

£19.95 (ex VAT £16.63)

Only 1 left in stock

The PM06 Power Module is a must-have for any drone builder. It supplies clean 5.2V power to your flight controller and 4 ESCs, with a wide input voltage range of 2S-14S and impressive current ratings of 70A continuous and 120A burst. It also offers precise current consumption and battery voltage measurements through an analog signal. Comes with pre-soldered wires, a capacitor, and an XT60 connector. Compact and lightweight at 35x35x5mm and 24g. Not compatible with Pixhawk 5X & 6X.

Not the cheapest?

We will try to beat it!

⚠️Always test your item before soldering, issues caused by soldering aren't covered by warranty.

SKU: H15019 Category: Brand:

Introducing the PM06 Power Module, the ultimate solution for supplying clean 5.2V power to your flight controller and distributing it to your 4 ESCs. With a wide input voltage range of 2S-14S, this power module can handle all your voltage needs. It has a continuous current rating of 70A and a burst current rating of 120A (for less than 60 seconds), ensuring that you have reliable power even during high-intensity flights.

In addition to its impressive power capabilities, the PM06 also features a voltage divider of 18.182 and amperes per volt of 36.364 for precise current consumption and battery voltage measurements. These measurements can be accessed through the 6 Pin JST-GH cable via an analog signal.

The PM06 comes with pre-soldered wires, a capacitor, and an XT60 connector for your convenience. However, please note that the XT60 plug and 12AWG wire are rated for 30A continuous current and 60A burst current (for less than 60 seconds). If you require higher current, it is recommended to change the plug type and wire size accordingly.

In terms of physical specifications, the PM06 has dimensions of 35x35x5mm and a mounting hole of 30.5mm*30.5mm. It is lightweight at only 24g, making it easy to integrate into your drone build. Please note that this PM06 Power Module uses analog data output and is not compatible with the Pixhawk 5X & 6X (a digital PM like the PM02D is required for these models).

Overall, the PM06 Power Module is a reliable and versatile choice for powering and distributing electricity in your drone build.

Specifications

  • Input voltage: 2S-14S
  • PCB Cont. Current Rating: 70A
  • PCB Burst Current Rating: 120A (<60 Sec)
  • Output: DC 5.2V & 3A Max (Note: To ensure proper heat dissipation, UBEC output current needs to be limited to <2A when using 14S battery.)
  • Voltage Divider: 18.182
  • Amperes per Volt: 36.364

Mechanical

  • Dimensions: 35x35x5mm
  • Mounting hole: 30.5mm*30.5mm
  • Weight: 24g

Included

  • 1x Power Module
  • 1x 80mm XT60 connector wire (pre-soldered)
  • 1x Electrolytic capacitor: 220uF 63V (pre-soldered)
  • 1x JST GH 6pin cable

Setup and Configuration Guide

Please see the official manual here-  Power Module – Holybro Docs

Weight 22 g
Dimensions 5 × 5 × 5 cm

Reviews

There are no reviews yet.

Only logged in customers who have purchased this product may leave a review.

Share this item on:

Product Meta Information:

SKU: H15019 Category: Brand:

Introducing the PM06 Power Module, the ultimate solution for supplying clean 5.2V power to your flight controller and distributing it to your 4 ESCs. With a wide input voltage range of 2S-14S, this power module can handle all your voltage needs. It has a continuous current rating of 70A and a burst current rating of 120A (for less than 60 seconds), ensuring that you have reliable power even during high-intensity flights.

In addition to its impressive power capabilities, the PM06 also features a voltage divider of 18.182 and amperes per volt of 36.364 for precise current consumption and battery voltage measurements. These measurements can be accessed through the 6 Pin JST-GH cable via an analog signal.

The PM06 comes with pre-soldered wires, a capacitor, and an XT60 connector for your convenience. However, please note that the XT60 plug and 12AWG wire are rated for 30A continuous current and 60A burst current (for less than 60 seconds). If you require higher current, it is recommended to change the plug type and wire size accordingly.

In terms of physical specifications, the PM06 has dimensions of 35x35x5mm and a mounting hole of 30.5mm*30.5mm. It is lightweight at only 24g, making it easy to integrate into your drone build. Please note that this PM06 Power Module uses analog data output and is not compatible with the Pixhawk 5X & 6X (a digital PM like the PM02D is required for these models).

Overall, the PM06 Power Module is a reliable and versatile choice for powering and distributing electricity in your drone build.

Specifications

  • Input voltage: 2S-14S
  • PCB Cont. Current Rating: 70A
  • PCB Burst Current Rating: 120A (<60 Sec)
  • Output: DC 5.2V & 3A Max (Note: To ensure proper heat dissipation, UBEC output current needs to be limited to <2A when using 14S battery.)
  • Voltage Divider: 18.182
  • Amperes per Volt: 36.364

Mechanical

  • Dimensions: 35x35x5mm
  • Mounting hole: 30.5mm*30.5mm
  • Weight: 24g

Included

  • 1x Power Module
  • 1x 80mm XT60 connector wire (pre-soldered)
  • 1x Electrolytic capacitor: 220uF 63V (pre-soldered)
  • 1x JST GH 6pin cable

Setup and Configuration Guide

Please see the official manual here-  Power Module – Holybro Docs

Weight 22 g
Dimensions 5 × 5 × 5 cm

Reviews

There are no reviews yet.

Only logged in customers who have purchased this product may leave a review.

HolyBro PM06 V2 2-14S Power Module

Only 1 left in stock