Not the cheapest?

Let us know, we will try to beat it!

Coupons PRICE MATCH

⚠️Check Before Soldering

If you need to solder or make any modifications to your item please test the item first. Modification or problematic soldering can cause damage not covered under warranty.

Share This Item:

HolyBro PM02D HV 2-12S Power Module

£23.95 (ex VAT £19.96)

Only 2 left in stock

SKU: H15011 Category: Tags: , Brand:

PM02D provides regulated power supply for your Pixhawk® 6X from the battery, as well as current consumption and battery voltage measurements, all through a 6pin cable. The on-board switching regulator outputs 5.2V and a maximum of 3A from LiPo batteries up to 6S.

HolyBro PM02D HV 2-12S Power Module

£23.95 (ex VAT £19.96)

Only 2 left in stock

PM02D provides regulated power supply for your Pixhawk® 6X from the battery, as well as current consumption and battery voltage measurements, all through a 6pin cable. The on-board switching regulator outputs 5.2V and a maximum of 3A from LiPo batteries up to 6S.

Not the cheapest?

We will try to beat it!

⚠️Always test your item before soldering, issues caused by soldering aren't covered by warranty.

SKU: H15011 Category: Tags: , Brand:

Note

  • PM02D HV version is supported by PX4. For Ardupilot, it is supported in version 4.4 and later. Full setup guide can be found here.
  • This PM uses I2C digital signal data output and is not compatible with flight controller that uses analog PM such as the Pixhawk 6C & Mini, Pixhawk4 & Mini, pix32 v5, or Durandal flight controllers.

PM02D provides regulated power supply for your Pixhawk® 5X & 6X from the battery, as well as current consumption and battery voltage measurements, all through a 6pin cable. The on-board switching regulator outputs 5.2V and a maximum of 3A from LiPo batteries up to 12S (HV). The Power Module comes completely assembled with XT60 connectors, wrapped in shrink tubing for physical damage protection.

It is not designed to power servos, please use your aircraft’s ESC/BEC for that. The Molex 2.00mm pitch CLIK-Mate Wire-to-Board connector is rated for 3.0A current per contact.

Specifications

  • Input voltage: 2-12S
  • PCB Cont. Current Rating: 60A
  • PCB Burst Current Rating: 100A (<60 Sec)
  • Max current sensing: 327A
  • Voltage and current monitor with I2C compatible interface
  • Outputs 5.2V and 3A max
  • Weight: 20g 

Current Rating

The PM02D comes with XT60 plugs with 14 AWG silicone wires rated for 30A continuous current and 60A burst current (<1 minute). If a higher current is needed, the plug type and wire size should be changed accordingly. You can refer to this chart as reference.

Pm02d hv chart

Pinout

Pm02d pinout

Setup:

If you are using the PM02D HV version, you must set SENS_EN_INA228 to enable.
Full setup guide can be found here.

Included

  • 1x PM02D Power Module
  • 1x 6pin 2.00mm pitch cable
Weight 22 g
Dimensions 1 × 8 × 12 cm

Reviews

There are no reviews yet.

Only logged in customers who have purchased this product may leave a review.

Share this item on:

Product Meta Information:

SKU: H15011 Category: Tags: , Brand:

Note

  • PM02D HV version is supported by PX4. For Ardupilot, it is supported in version 4.4 and later. Full setup guide can be found here.
  • This PM uses I2C digital signal data output and is not compatible with flight controller that uses analog PM such as the Pixhawk 6C & Mini, Pixhawk4 & Mini, pix32 v5, or Durandal flight controllers.

PM02D provides regulated power supply for your Pixhawk® 5X & 6X from the battery, as well as current consumption and battery voltage measurements, all through a 6pin cable. The on-board switching regulator outputs 5.2V and a maximum of 3A from LiPo batteries up to 12S (HV). The Power Module comes completely assembled with XT60 connectors, wrapped in shrink tubing for physical damage protection.

It is not designed to power servos, please use your aircraft’s ESC/BEC for that. The Molex 2.00mm pitch CLIK-Mate Wire-to-Board connector is rated for 3.0A current per contact.

Specifications

  • Input voltage: 2-12S
  • PCB Cont. Current Rating: 60A
  • PCB Burst Current Rating: 100A (<60 Sec)
  • Max current sensing: 327A
  • Voltage and current monitor with I2C compatible interface
  • Outputs 5.2V and 3A max
  • Weight: 20g 

Current Rating

The PM02D comes with XT60 plugs with 14 AWG silicone wires rated for 30A continuous current and 60A burst current (<1 minute). If a higher current is needed, the plug type and wire size should be changed accordingly. You can refer to this chart as reference.

Pm02d hv chart

Pinout

Pm02d pinout

Setup:

If you are using the PM02D HV version, you must set SENS_EN_INA228 to enable.
Full setup guide can be found here.

Included

  • 1x PM02D Power Module
  • 1x 6pin 2.00mm pitch cable
Weight 22 g
Dimensions 1 × 8 × 12 cm

Reviews

There are no reviews yet.

Only logged in customers who have purchased this product may leave a review.

HolyBro PM02D HV 2-12S Power Module

Only 2 left in stock