Not the cheapest?
Let us know, we will try to beat it!
Happymodel Moblite7 Walksnail 1s 75mm Brushless HD Whoop
-15%
£164.99 – £201.89
The Moblite7 from Happymodel is a 1S brushless whoop that includes the Walksnail Avatar Nano HD FPV system. This givs you crisp, clear HD low latency in the form factor of a tiny whoop without sacrificing flight performance thanks to the ultra-lightweight walksnail HD Air unit.
Not the cheapest?
We will try to beat it!
⚠️Always test your item before soldering, issues caused by soldering aren't covered by warranty.
Features
- Lightweight 1S whoop with Walksnail Avatar Nano FPV TX unit onboard
- Powerful and efficient
- SuperBee F4 AIO Flight Controller
- Walksnail Avatar Mini digital FPV system
- EX1002 brushless motors
- Low profile Canopy design
Specifications
- Brand Name: Happymodel
- Model: Moblite7 Walksnail
- Frame wheelbase: 75mm
- Weight: 33.5 gram without battery
- Size: 98mm*98mm*50mm
- Receiver option:
- SPI ELRS 2.4GHz
- SPI FRSKY 2.4GHz
- Compatible with 1S Lipo battery or Lihv battery
- Battery Plug: PH2.0
| Flight controller SuperbeeF4 Lite ELRS/FRSKY |
SPI ELRS version Firmware target: CrazybeeF4SX1280 SPI FRSKY version Firmware target: CrazybeeF4FR MCU:STM32F411CEU6 (100MHz, 512K FLASH) Sensor: ICM20689 or ICM42688P or BMI270(SPI connection) Power supply: 1S Lipo Lihv battery input (DC 2.8V~4.35V) Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 ready Built-in Betaflight OSD(SPI Control) Built-in SPI Frsky/ExpressLRS receiver Built-in 5V 1A BEC Built-in voltage detection |
| Onboard 4in1 ESC | MCU upgraded to EFM8BB21 Power supply: 1S LiPo/LiPo HV (2.8v~4.35v) Currents: 5A continuous peak 6A (5 seconds) Support BLHeliSuite programmable Factory firmware: O_H_5_REV16_8.HEX Default protocol: DSHOT150/DSHOT300/DSHOT600 |
| Onboard SPI ExpressLRS 2.4GHz Receiver | Packet Rate option: 25Hz/50Hz/150Hz/250Hz/500Hz RF Frequency: 2.4GHz Telemetry output Power: <12dBm Receiver protocol: SPI ExpressLRS Could bind with ELRS V2.0 firmware TX module |
| Onboard Frsky SPI D8 /D16 2.4GHz Receiver | SPI BUS receiver Frsky D8/D16 compatible Compatible Non EU transmitter D8 model and EU-LBT(Frsky_x_lbt) Channels: 8ch or 16ch Failsafe support No ground interference ( Transmitter and receiver 1 m from the ground): 100m~200m Based on CC2500 RF module Compatible with Futaba S-FHSS , Redpine protocol |
| Motor | Model: EX1002 20000KV Configu-ration:9N12P Stator Diameter:10mm Stator Length:2mm Shaft Diameter:Φ1.5mm Motor Dimension(Dia.*Len):Φ13.5mm*12.5mm Weight(g):2.5g No.of Cells(Lipo):1S only |
| Propeller Gemfan 1610-2 Bi-blades | Weight:0.24g Material: PC Pitch:1 inchProps Dia:40mm Center Hole Dia:1.5mm |
| Avatar mini VTX | Model: Avatar mini 1s module Communication Frequency: 5.725-5.850 GHz Transmitter Power(EIRP): FCC:<25.5dBm; CE:<14dBm; SRRC: <20dBm;MIC:<25dBm l/o Interface: JST1.O*6(Power in)JST1.O*4(USB) Mounting Holes: 25.5*25.5 mm Dimensions: 33*33*6.5 mm Storage: 8G Recording: 1080p/720p Weight: 6.8 g Operating Temperature: -20-40℃ Channels: 8 Wide Power lnput: 3.1V-5V Supported FC System: Betaflight OSD: Canvas mode Bitrate: 25mbps / 50mbps Latency: Average delay 22ms Antenna connector: IPEX |
| Avatar nano FPV Camera | Model: Avatar nano lmage Sensor: 1/2.7”Inch Resolution: 1080P/6Ofps,720P/120fps,72OP/6Ofps Ratio: 16/9 4/3 Lens: 2.1mm FOV 170° Aperture: F2.0 Shutter: Rolling shutter Min.Illumination: 0.001Lux Weight: 3.5g Dimensions: 14*14*17mm Coaxial Cable: 45mm |
Resources
Included
- 1 x Happymodel Moblite7 HD Walksnail Avatar
- 1x spare canopy (depending on supply so you may not receive this)
- 1x screw driver and prop removal tool (depending on supply so you may not receive this)
| Weight | 200 g |
|---|---|
| Dimensions | 10 × 10 × 5 cm |
| Receiver | |
| KV Rating | |
| Prop Diameter | |
| FPV System |
Only logged in customers who have purchased this product may leave a review.
Share this item on:
Product Meta Information:
Reviews
There are no reviews yet.