Features
- The lightest 1s 75mm brushless whoop
- Powerful and efficient
- The lightest 1s AIO 5IN1 F4 flight controller
- New Unibell EX0802 brushless motors
- Low profile Canopy design
- VTX power switchable 25mw~200mw
Specifications
- Brand Name: Happymodel
- Item Name: Moblite7 1S 75mm ultra light brushless whoop
- Wheelbase: 75mm
- Size: 97mm*97mm*25mm
- Weight: 19.5g (without battery)
- Weight:36g(with Original 1s 650mah Lipo battery )
Motor | Mode: EX0802 19000KV Configu-ration:9N12P Stator Diamter:8mm Stator Length:2mm Shaft Diameter:Φ1mm Motor Dimension(Dia.*Len):Φ10.5mm*14.9mm Weight(g):1.7g No.of Cells(Lipo):1S only |
Flight controller | (Frsky SPI RX version) DiamondF4 FR FC Firmware target: CrazybeeF4FR (Flysky SPI RX version)DiamondF4 FS FC Firmware target: CrazybeeF4FS MCU:STM32F411CEU6 (100MHZ, 512K FLASH) Sensor: MPU-6000(SPI connection) Original whoop size compatible Power supply: 1S battery input (DC 2.9V-4.35V) Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 ready Built-in Betaflight OSD(SPI Control) Built-in 5.8G VTX Built-in SPI Frsky/Flysky receiver Built-in 5V 1A BEC |
Onboard 4in1 ESC | MCU upgraded to EFM8BB21 Power supply: 1S LiPo/LiPo HVCurrent: 5A continuous peak 6A (3 seconds) Support BLHeliSuite programmable Factory firmware: O_H_50_REV16_8.HEX Default protocol: DSHOT600 |
Onboard Frsky SPI D8 receiver Version | SPI BUS receiver Frsky D8 compatible Compatible Non EU transmitter D8 modelChannels: 8ch Failsafe support No ground interference ( Transmitter and receiver 1 m from the ground): 200m~300m |
Onboard Flysky SPI receiver Version | SPI BUS receiver Protocol: AFHDS and AFHDS-2A Switchable Channels: 8ch(AFHDS) or 14ch(AFHDS-2A) No ground interference ( Transmitter and receiver 1 m from the ground): 200~300m Failsafe support |
Onboard 5.8g VTX | Output power: 25mw~200mw switchable Frequency: 40CH Input voltage: 3.3V 5.5V Current consumption: 300mA(type) Frequency: 5.8GHz 5bands 40 channels(include Race band)Smartaudio ready |
Runcam Nano 3 | Model: RunCam Nano 3 Image Sensor: 1/3″ CMOS Horizontal Resolution: 800TVL Lens : 2.3mm(M6.5) FOV 140° Signal System: PAL/NTSC Non Switchable S/N Ratio: >50dB Electronic Shutter Speed: Auto Auto Gain Control (AGC): Auto Min. Illumination: 0.01Lux@1.2F D-WDR: Auto Day/Night: Color Power:DC 3-5.5V Current: 110mA@5V 120mA@3.3V Housing Material: ABS Net Weight: 1.2g Dimensions: L14mm*W14mm*H9mm |
Lipo Battery | Capacity:650mAh Voltage:3.8v Continuous Discharge Rate: 30C Instantaneous discharge rate: 60C Size: 60mmx18mmx8mm Weight: 16g Connector: PH2.0 |
Included
- 1 x Happymodel Moblite7 75mm Whoop RC FPV Racing Drone
- Option1: 1 x DiamondF4 FR built-in SPI Frsky Receiver
- Option2: 1 x DiamondF4 FS built-in SPI Flysky Receiver
- 4 x EX0802 KV19000 Unibell Brushless Motor
- 1 x HQPROP 40MMX2 Propeller(4cw+4ccw)
- 1 x Runcam Nano 3 FPV Camera
- 1 x Built-in 5.8G 40ch 25mw-200mw VTX
- 2 x 1S 650mah Lipo Battery
- 1 x Propeller Disassemble Tool
- 1 x Screwdriver
- 1 x Happymodel Carry Case
Jason (verified owner) –
A mixed bag of a whoop. Good thing you get a screwdriver and a spare frame in the box as mine was heavily bent out of shape. I had to swap the frame straight away it was that bad. The camera mounting system is what it is – its ok as long as you make sure you check the cams alignment before every flight. The best part of the whole kit is the FC board with everything built in. Leaving on a positive note – flying at a generous pace round the in-house track ( over 2 floors ) – the included 650mah lipos got me an amazing 11m 30s !!!