Not the cheapest?

Let us know, we will try to beat it!

Coupons PRICE MATCH

⚠️Check Before Soldering

If you need to solder or make any modifications to your item please test the item first. Modification or problematic soldering can cause damage not covered under warranty.

Share This Item:

Crazybee F4 Lite Whoop Flight Controller with VTX

(1 customer review)

£29.95

SKU: CRF4LITE Categories: , , Tags: , Brand:

This is the the flight controller used on the mobula6.  It features a with a built in SPI receiver (FRsky / Flysky), MPU6000 gyro, betaflight OSD and a F411 MCU.  All this packed into a tiny whoop form factor FC.

 

Crazybee F4 Lite Whoop Flight Controller with VTX

£29.95

This is the the flight controller used on the mobula6.  It features a with a built in SPI receiver (FRsky / Flysky), MPU6000 gyro, betaflight OSD and a F411 MCU.  All this packed into a tiny whoop form factor FC.

 

Not the cheapest?

We will try to beat it!

⚠️Always test your item before soldering, issues caused by soldering aren't covered by warranty.

SKU: CRF4LITE Categories: , , Tags: , Brand:

This is the the flight controller used on the mobula6.  It features a with a built in SPI receiver (FRsky / Flysky), MPU6000 gyro, betaflight OSD and a F411 MCU.  All this packed into a tiny whoop form factor FC.

Specification

Crazybee F4 LiteFlight Controller
Built-in ESC & Receiver & VTX
Frsky SPI RX version) CRAZYBEE F4 Lite Frsky version Firmware target: CrazybeeF4FR
(Flysky SPI RX version) CRAZYBEE F4 Lite Flysky version Firmware target: CrazybeeF4FS
MCU:STM32F411CEU6 (100MHZ, 512K FLASH)
Sensor: MPU-6000(SPI connection)
Board size: 28.5 * 28.5MM
Power supply: 1S battery input (DC 2.9V-4.35V)
Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 ready
Built-in Betaflight OSD(SPI Control)
Built-in 5.8G VTX
Built-in SPI Frsky/Flysky receiver
Built-in 5V 1A BEC
Built-in voltage detection
Onboard Frsky Receiver Version
SPI BUS receiver Frsky D8 compatible
Compatible Non EU transmitter D8 model
– Frsky_x_lbt Support EU LBT Radio Transmitter
Channels: 8ch
Failsafe support
No ground interference ( Transmitter and receiver 1 m from the ground): 100m~200m
Onboard Flysky Receiver Version
SPI BUS receiver
Protocol: AFHDS and AFHDS-2A Switchable
Channels: 8ch(AFHDS) or 14ch(AFHDS-2A)
No ground interference ( Transmitter and receiver 1 m from the ground): 100~200m
Failsafe support
Onboard 5A BLheli_S 4in1 ESC
MCU upgraded to EFM8BB21
Power supply: 1S LiPo/LiPo HV
Current: 5A continuous peak 6A (3 seconds)
Support BLHeliSuite programmable
Factory firmware: O_H_5_REV16_7.HEX
Default protocol: DSHOT600
Onboard 5.8G 40CH 25mW VTX Output power: 25mw
Frequency: 40CH
Input voltage: 3.3V 5.5V
Current consumption: 300mA(type)
Frequency: 5.8GHz 5bands 40 channels
With Race band

Included

  • 1x Crazybee F4 Lite Flight Controller
  • 4x Anti-Vibration Ball
  • 4x Screws

 

Weight 50 g
Dimensions 5 × 5 × 1 cm
Receiver

,

1 review for Crazybee F4 Lite Whoop Flight Controller with VTX

  1. MartianMcFlyFpv (verified owner)

    I good board but quite delicate and not very friendly if you try to de-pin them. The newer 5in1 diamond would be a better choice for that.
    All in, this board is fine and functional but expect to go through a few of these if you are whooping the arse off it! xD

    Martian McFly FPV

Only logged in customers who have purchased this product may leave a review.

Share this item on:

Product Meta Information:

SKU: CRF4LITE Categories: , , Tags: , Brand:

This is the the flight controller used on the mobula6.  It features a with a built in SPI receiver (FRsky / Flysky), MPU6000 gyro, betaflight OSD and a F411 MCU.  All this packed into a tiny whoop form factor FC.

Specification

Crazybee F4 LiteFlight Controller
Built-in ESC & Receiver & VTX
Frsky SPI RX version) CRAZYBEE F4 Lite Frsky version Firmware target: CrazybeeF4FR
(Flysky SPI RX version) CRAZYBEE F4 Lite Flysky version Firmware target: CrazybeeF4FS
MCU:STM32F411CEU6 (100MHZ, 512K FLASH)
Sensor: MPU-6000(SPI connection)
Board size: 28.5 * 28.5MM
Power supply: 1S battery input (DC 2.9V-4.35V)
Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 ready
Built-in Betaflight OSD(SPI Control)
Built-in 5.8G VTX
Built-in SPI Frsky/Flysky receiver
Built-in 5V 1A BEC
Built-in voltage detection
Onboard Frsky Receiver Version
SPI BUS receiver Frsky D8 compatible
Compatible Non EU transmitter D8 model
– Frsky_x_lbt Support EU LBT Radio Transmitter
Channels: 8ch
Failsafe support
No ground interference ( Transmitter and receiver 1 m from the ground): 100m~200m
Onboard Flysky Receiver Version
SPI BUS receiver
Protocol: AFHDS and AFHDS-2A Switchable
Channels: 8ch(AFHDS) or 14ch(AFHDS-2A)
No ground interference ( Transmitter and receiver 1 m from the ground): 100~200m
Failsafe support
Onboard 5A BLheli_S 4in1 ESC
MCU upgraded to EFM8BB21
Power supply: 1S LiPo/LiPo HV
Current: 5A continuous peak 6A (3 seconds)
Support BLHeliSuite programmable
Factory firmware: O_H_5_REV16_7.HEX
Default protocol: DSHOT600
Onboard 5.8G 40CH 25mW VTX Output power: 25mw
Frequency: 40CH
Input voltage: 3.3V 5.5V
Current consumption: 300mA(type)
Frequency: 5.8GHz 5bands 40 channels
With Race band

Included

  • 1x Crazybee F4 Lite Flight Controller
  • 4x Anti-Vibration Ball
  • 4x Screws

 

Weight 50 g
Dimensions 5 × 5 × 1 cm
Receiver

,

1 review for Crazybee F4 Lite Whoop Flight Controller with VTX

  1. MartianMcFlyFpv (verified owner)

    I good board but quite delicate and not very friendly if you try to de-pin them. The newer 5in1 diamond would be a better choice for that.
    All in, this board is fine and functional but expect to go through a few of these if you are whooping the arse off it! xD

    Martian McFly FPV

Only logged in customers who have purchased this product may leave a review.

Crazybee F4 Lite Whoop Flight Controller with VTX
£29.95 Select options